The video introduces the GForce Arms BLADE6, a 9mm pistol-caliber carbine that uses Glock-pattern magazines and is positioned as a value-focused option. Technical specifications are outlined first: it has a 6-inch threaded barrel made from 4140 steel with a 1/2x28 thread pitch and a substantial metal thread protector. The listed overall length is 15 inches, with a stated weight of 5.7 pounds and a quoted trigger pull of 5.5 pounds. The upper assembly and rail sections are primarily aluminum. The pistol ships with flip-up polymer sights and a Glock-pattern magazine, described as larger than a standard Glock mag. The plan for the video is to go through the gun from front to rear, then verify the published specs with actual measurements, weight checks, and trigger pull testing.
The front of the BLADE6 features a notably large, knurled metal thread protector on the 9mm barrel, described as unusually beefy for this type of pistol. The knurling is split into two sections to make removal and installation easier, and it contributes to a robust overall look. Moving rearward, the gun has a full-length Picatinny rail on top with no breaks, designed as a single solid piece of metal. Additional Picatinny sections are located on both sides and on the bottom of the front end, allowing for mounting optics, lights, or other accessories. A shallow channel runs along the top of the receiver, which could serve as a rudimentary backup sighting reference in a pinch, though it is not intended as a primary sighting system. The construction of the rail and front end feels rigid and solid, emphasizing durability over light weight.
The BLADE6 uses a side charging handle that offers an HK-style slap to release the bolt, and the handle is non-reciprocating during firing. With Glock-pattern magazines, the pistol provides last-round bolt hold open, and there is a dedicated bolt catch on the left side. The charging handle and bolt system are described as solid and satisfying in operation. The gun includes sling attachment points on both sides near the front, suitable for clip-in slings. Moving back, there are ambidextrous safety selectors, while the magazine release itself is located on one side only. The grip is a hybrid design with a polymer core and a rubber overmolded exterior. It includes a finger groove and moderately aggressive texturing to improve control when hands are sweaty. Two QD sling sockets are positioned on either side of the rear portion of the receiver, placing a single-point sling in a comfortable spot for a compact PDW-style or PCC-style setup. A rear Picatinny rail section allows mounting of various braces.
The magazine well on the BLADE6 is slightly flared to aid in faster reloads. It is integrated into the metal lower rather than being a separate plastic add-on, and it feels rigid and substantial. The pistol offers two magazine release methods: a paddle-style release accessible from the side in an AR-like fashion, and a second release at the rear of the magazine well in an MP5-style position. The lower release is more extended than a traditional MP5 release, providing an additional option for different grip and reload preferences. The trigger is demonstrated and described as a single-stage design with very little take-up. The break is crisp, and the reset has a small amount of movement before returning to the starting point. Overall, the trigger is characterized as short and conducive to firing strings quickly while maintaining control, with a feel that aligns well with the quoted pull weight.
To verify the factory-listed trigger pull of 5.5 pounds, a trigger pull gauge is used with the pistol supported for stability. After clearing the firearm and removing the magazine, the gauge reading comes out to approximately 5.39 pounds. This result is presented as very close to the stated 5.5-pound specification. It is suggested that pulling from different positions on the trigger shoe, such as closer to the tip, might yield slightly lighter readings, potentially around the mid-4-pound range, but the general expectation is a 5- to 6-pound pull. The test confirms that the trigger weight is consistent with the manufacturer’s published numbers, reinforcing the earlier subjective impression of a short, crisp single-stage trigger suitable for controlled, quick shooting.
The pistol’s actual weight is checked on a scale. With the magazine inserted, the BLADE6 weighs about 6.22 pounds. Removing the magazine brings the weight down to approximately 5.98 pounds, effectively right at 6 pounds, which is slightly heavier than the listed 5.7-pound specification. This extra weight is attributed to the robust construction and numerous features. Length is measured from muzzle to rear, resulting in roughly 15.75 inches, again a bit longer than the quoted 15 inches. Height with the magazine inserted is about 9.5 inches. Measuring from the grip to the top of the receiver without the magazine yields a height of around 7.25 inches. Thickness across the main body is estimated at about 1.5 to 1.75 inches. These measurements give a realistic sense of the pistol’s footprint for storage or bag carry and highlight that it is compact but not ultralight.
The video concludes by revisiting what comes in the box with the GForce Arms BLADE6. The pistol includes polymer flip-up front and rear sights, allowing it to be used immediately without purchasing additional optics. A small cleaning kit is also included. The threaded barrel makes it ready for a suppressor or other muzzle device, and the extensive Picatinny rail space supports mounting red dot optics, lights, or other accessories. The rear Picatinny section is suitable for attaching a brace, and the multiple sling mounting points support different carry setups. Overall, the BLADE6 is presented as a feature-rich 9mm PCC with solid construction, a short single-stage trigger, and verified specs that slightly exceed the listed weight and length, giving potential users a clear picture of its handling and configuration options.
Loading...